Corrugated Carton Sheet Production Die Cuting Machine

Corrugated Carton Sheet Production Die Cuting Machine

 

 
 

  1. FEEDER (Max minimize direct edge feeder)
  1. New up graded, exact same as Max lower lead edge feeder, a lot more correct and good feeding.
  2. Uncommon jogger at feeder to get ready for the attainable foreseeable future in line procedure with pre feeder (optional).
  3. Pneumatic side thrust guide plates (remaining and correct sides).
  4. Remaining and correct side guides, independently situation adjustable and sign up facet at selection per box format.
  5. Substantial vacuum blower with silencer and valving method.

 

  1. DIECUTTING Part
  1. Crank and worm gear, toggle travel technique for the reduce platen.
  2. The cellular platen stroke is enhanced from 71mm to 95mm for handling corrugated board (especially AB Flute) smoother.
  3. Stationary substantial precision higher platen.
  4. Protection door and die chaser basic safety locking program.
  5. Substantial torque pneumatic clutch/split for good clutch on and reputable breaking, and special air inlet system to handle the air volume for clean device start and stop.
  6. Air cushion beneath the slicing plate for simple reducing plate in and out.
  7. Gear major drive.
  8. Overloading safety torque limit clutch.
  9. Condition-of-the-artwork three cam index gripper chain travel.
  10. Centre line system appropriate to Heart Line II, tends to make the reducing die and stripping die centered speedily.
  11. High quality precision alloy gripper bars, each with twelve unique hardened grippers to make certain agency get of the sheet at high pace.
  12. Sheet arrival and departure check photograph sensor.
  13. Left and right entrance lay locking blocks, separating and synchronizing adjustment CZPT.
  14. Chain manual rail use VL compound to increase abrasive resistance and seismic resistance.
  15. Self-diagnostic problems show.
  16. Digital pace screen.
  17. Computerized recycling lubrication system with oil force gauge and oil pressure switch.
  18. Computerized principal gripper push chain lubrication.

 

  1. STRIPPING Section
  1. Centerline method (appropriate to Centerline II).
  2. 400mm upper stripping body raiser boosts the operation place, more operator friendly.
  3. Motorized upper frame suspending hoister.
  4. Guide edge waste removing system.
  5. Centerline method for rapid stripping die established up.

 

  1. Shipping
  1. Escalator shipping fork with non-end air cylinder for neat and constructive delivery and conveyor belt shipping and delivery table to shield the sheets from scratches.
  2. Bundle supply with pre-set counter requesting only a single sheet interval in non-end operation at 4500S/H production speed.
  3. The bundle supply table can be geared up for foreseeable future relationship with breaker for in line procedure (to be necessary at buy).
  4. Full stripping with/CZPT direct edge waste stripping convertible by a single button, no tool alter, more operator friendly and risk-free operation.
  5. CZPT loaded adjustable chain rigidity back again buffering wheel to preserve the chain stress continuous and sleek gripper bar movement.

 

No. Design RYPE-1620SA
one Maximum Sheet Measurement 1620x1200mm
two Minimal Sheet Size 650x450mm
three Maximum Slicing Measurement 1600x1180mm
4 Inner CZPT Measurement 1630x1210mm
5 Highest Mechanical Pace 5000 cycles/hour
6 Greatest Cutting Stress 400 tons
7 Stock Selection E, B,C,A and AB flute corrugated board (one~8.5mm)
eight Least Gripper Margin 6~12mm
nine Bare minimum Gripper Waste 12mm(Distance from first knife to paper edge)
10 Slicing Rule Top 23.8mm
11 Whole Electrical power Needed 35 KW
twelve Main Motor Electricity 22 KW
13 CZPTal Electrical power 380V, 50HZ, 3-stage
14 Air Pump Displacement .7m³/min
15 Mobile Reduced Platen Changing Range ±1.5mm
16 Internet Fat of Device 32 tons
17 Gross Weight of Device 39.5 tons
18 Equipment Proportions (LxWxH) 9980×5670 x2480 mm (involves strolling board)

Corrugated Carton Sheet Production Die Cuting Machine